基于碰撞性能的车身刚度链设计方法*

doi:10.19562/j.chinasae.qcgc.2018.012.008

汽车工程 ›› 2018, Vol. 40 ›› Issue (12): 1426-1434.doi: 10.19562/j.chinasae.qcgc.2018.012.008

基于碰撞性能的车身刚度链设计方法^*

郭毅, 刘子建, 秦欢

湖南大学,汽车车身先进设计制造国家重点实验室,长沙 410082

收稿日期:2017-10-09 出版日期:2018-12-25 发布日期:2018-12-25
通讯作者: 刘子建,教授,博士生导师,E-mail:zijianliu@hnu.edu.cn
基金资助:
国家自然科学基金(51475152)资助

A Design Method of Car Body Stiffness Chain Based on Crashworthiness

Guo Yi, Liu Zijian, Qin Huan

Hunan University, State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body, Changsha 410082

Received:2017-10-09 Online:2018-12-25 Published:2018-12-25

摘要/Abstract

摘要： 本文中综合考虑车身动态与静态刚度和正面碰撞安全性,提出了一种车身正向概念设计方法。首先,根据车身A级面和整体布置,建立了车身简化几何模型,确定了19个车身主断面,并基于梁单元理论和传递矩阵法建立车身刚度链数学模型。接着,采用碰撞经验公式设计矩形前纵梁,以等效静态载荷模拟车身正面碰撞动态加载,并提出了基于等效静态加载条件下的车身变形要求。然后,以车身质量最轻为目标,车身静态刚度、1阶模态和碰撞变形为约束,采用遗传算法优化车身各梁单元主断面参数。最后对某一近似标杆车进行有限元仿真,计算其车身静刚度与模态,与本文中的刚度链方法计算结果进行对比,验证了该方法的可行性。

关键词: 正面碰撞, 正向设计, 刚度链, 等效静态载荷

Abstract: Concurrently considering the dynamic and static stiffness and frontal crash safety, a forward conceptual design method of car body is presented in this paper. Firstly according to class A surface and vehicle general layout, a simplified geometric model for car body is established, 19 main cross-sections of the body is determined, and the stiffness chain model of car body is built based on beam element theory and transfer matrix method. Then rectangular front longitudinal beam is designed by using collision empirical formula, the frontal crash dynamic loading of car body is simulated by equivalent static load, and the requirements of car body deformation are put forward based on equivalent static loading condition. Next, a simulation on the main cross-section parameters of each beam element of car body is conducted by using genetic algorithm, with minimizing car body mass as objective and the static stiffness, the first order mode and collision deformation of car body as constraints. Finally, a finite element simulation is performed on an approximate benchmark car, with its static stiffness and vibration modes of car body calculated and compared with that by using stiffness chain method, verifying the feasibility of the method adopted.

Key words: frontal crash, forward design, stiffness chain, equivalent static load

郭毅, 刘子建, 秦欢. 基于碰撞性能的车身刚度链设计方法^*[J]. 汽车工程, 2018, 40(12): 1426-1434.

Guo Yi, Liu Zijian, Qin Huan. A Design Method of Car Body Stiffness Chain Based on Crashworthiness[J]. , 2018, 40(12): 1426-1434.

参考文献

[1] QUINN G C. Full automobile topology design optimized to maximize structural stiffness subject to multiple static load cases including inertial relief[C].13th AIAA/ISSMO Multidisciplinary Analysis Optimization Conference,2010:13-15.
[2] 常伟波,张维刚,崔杰,等.基于正面碰撞的轿车车身正向概念设计的研究[J].汽车工程,2012,34(5):447-451.
[3] YI S I, LEE J Y, PARK G J. Crashworthiness design optimization using equivalent static loads[J]. Proceedings of the Institution of Mechanical Engineers,2012,226(1).
[4] 高云凯,田林雳.基于等效静态载荷法的车身碰撞拓扑优化[J].同济大学学报(自然科学版),2017,45(3):391-397.
[5] QIN H, LIU Z, LIU Y, et al. An object-oriented MATLAB toolbox for auto-motive body conceptual design using distributed parallel optimization[J]. Advances in Engineering Software,2017,106(4):19-32.
[6] 刘子建,饶俊威,刘瑜,等.基于主断面参数的车身结构刚度链快速求解[J].湖南大学学报(自然科学版),2017,44(2):1-8.
[7] 陈毅强,刘子建.电动汽车车身的回传射线矩阵刚度链分析方法[J].中国机械工程,2016,27(23):3252-3258,3265.
[8] 刘保公,刘子建,周小龙,等.基于刚度链的纯电动汽车车身主断面优化设计[J].中南大学学报(自然科学版),2017,48(4):959-967.
[9] 荆友录.矩形截面薄壁梁轴向耐撞性的结构研究[J].山东交通学院学报,2009,17(1):5-8.
[10] 陈吉清,周鑫美,饶建强,等.汽车前纵梁薄壁结构碰撞吸能特性及其优化的研究[J].汽车工程,2010,32(6):486-492.
[11] 黄靖.汽车碰撞过程中加速度特征对乘员损伤的影响分析[D].大连:大连理工大学,2009.
[12] 田晟.单元薄壁矩形截面梁的平均压溃力研究[J].华南理工大学学报(自然科学版),2014(9):102-106.
[13] 刘洋.基于LS-DYNA的汽车正面碰撞计算机模拟仿真[D].成都:西华大学,2011.
[14] KIM Y I, PARK G J. Nonlinear dynamic response structural optimization using equivalent static loads[J]. Computer Methods in Applied Mechanics & Engineering,2010,199(9-12):660-676.
[15] 陈涛,陈自凯,段利斌,等.针对结构动态非线性优化问题的ESLM梯度优化方法[J].机械工程学报,2015,51(8):116-124.
[16] 高云凯,孙芳,程金山,等.轿车前舱结构性能综合优化[J].中国机械工程,2010(4):394-399.
[17] MALEN D E. Fundamentals of automobile body structure design[M]. Pen-nsylvania USA: SAE Interational,2011.

基于碰撞性能的车身刚度链设计方法^*

A Design Method of Car Body Stiffness Chain Based on Crashworthiness

PDF (PC)

赞

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 11

Metrics

本文评价

推荐阅读 10

[1]	唐洪斌,张君媛,刘国军. 正面碰撞等级预估方法[J]. 汽车工程, 2022, 44(3): 392-398.
[2]	李海岩,苏航杰,祝贺,刘冲,王彦鑫,崔世海,贺丽娟,王一达,吕文乐. 中国体征3岁儿童乘员损伤仿生模型在C-NCAP正面碰撞测试仿真中的应用[J]. 汽车工程, 2022, 44(12): 1944-1953.
[3]	刘刚,洪亮,葛如海. 面向“离位”儿童乘员的常开式安全气囊优化设计[J]. 汽车工程, 2022, 44(1): 94-104.
[4]	宋祥文,邹猛,许述财,黄彬兵. 误使用工况下儿童安全座椅安全性的开发与验证[J]. 汽车工程, 2021, 43(12): 1780-1786.
[5]	武和全, 彭金平, 邓晓顺, 金鑫, 胡林. 正面碰撞中的老年驾驶员胸部响应研究^*[J]. 汽车工程, 2020, 42(8): 1050-1059.
[6]	胡建锋, 王鑫, 杜保华, 金云光, 田亮, 欧阳明, 高凯, 武韩. 汽车侧门正向设计中关门能量的计算[J]. 汽车工程, 2020, 42(10): 1440-1447.
[7]	王琼, 黄志亮. 含概率区间混合不确定性的汽车正面碰撞可靠性优化设计^*[J]. 汽车工程, 2019, 41(5): 545-549.
[8]	葛如海, 顾瑶芝, 蔡朝阳, 黄可鑫, 陈宇航. 正面碰撞前后双气室气囊的设计与优化^*[J]. 汽车工程, 2019, 41(4): 411-416.
[9]	颜凌波,解文娜,许伟,曹立波,戴宏亮,张恺. 正面碰撞中基于中国人体尺寸的假人损伤响应研究^*[J]. 汽车工程, 2019, 41(3): 289-297.
[10]	郑建洲, 陈有松, 吕斌斌, 尹浩庆. 基于Kriging模型的座椅子系统安全性能优化研究[J]. 汽车工程, 2019, 41(11): 1301-1307.
[11]	陈媛媛,郑玲. 基于代理模型的汽车正撞安全性仿真优化[J]. 汽车工程, 2018, 40(6): 673-.