乘用车液力变矩器优化设计研究综述*

doi:10.19562/j.chinasae.qcgc.2020.08.013

Abstract

Abstract: The research progress and status quo of each stage in the optimization design process for hydraulic torque converter (HTC) are reviewed. Four aspects of researches on HTC including design and parameterization methods, the effects of design parameters on performances, performance prediction models, and design optimization methods are expounded, and the applications of the new technology in HTC are briefed. The research results of each stage are summarized. Finally the further research directions on HTC are look ahead.

Key words: hydraulic torque converter, design optimization, parameterization, performance prediction, review

Wu Guangqiang, Chen Jie. Review on Design Optimization Research of Hydraulic Torque Converter for Passenger Vehicles[J].Automotive Engineering, 2020, 42(8): 1090-1096.

References

[1] 魏巍,刘城,闫清东.柔性扁平循环圆液力元件叶栅系统设计方法[J].农业机械学报,2011,42(4).DOI:10.3969/j.issn.1000-1298.2011.04.007.
[2] 刘春宝,马文星,朱喜林,等.基于椭圆循环圆的轿车扁平液力变矩器设计[J].吉林大学学报(工学版),2010,40(4):1039-1043.
[3] 刘城.向心涡轮式液力变矩器叶栅系统参数化设计方法研究[D].北京:北京理工大学,2015.
[4] 刘城,闫清东,魏巍.液力变矩器导轮叶片造型及优化设计[J].哈尔滨工业大学学报,2016.DOI:10.11918/j.issn.0367-6234.2016.01.017.
[5] 王立军,吴光强,王欢.基于叶片角变化规律的液力变矩器改型设计法[J].同济大学学报(自然科学版),2010,39(11):1673-1679.DOI:10.3969/j.issn.0253-374x.2011.11.020.
[6] KIETLINSKI T, FINGERMAN M. 248mm elliptical torque converter from daimlerchrysler corporation[C]. SAE Paper 2007-01-0241.
[7] HACHISUWA I, KATO N, KUSAMOTO D, et al. Development of compact torque converter with new multiple disk clutch for Toyota new FWD eight-speed transmission direct shift-8AT[C]. SAE Paper 2017-01-1118.
[8] USUI T, OKAJI T, MURAMATSU T, et al. Development of a compact ultra-flat torque converter equipped with a high-performance damper[J]. SAE International Journal of Engines,2015,8(3):1374-1378.
[9] EJIRI E, KUBO M. Influence of the flatness ratio of an automotive torque converter on hydrodynamic performance[J]. Journal of Fluids Engineering,1999,121(3):614-620.
[10] LIU C B, LIU C S, MA W X. Mathematical model for elliptic torus of automotive torque converter and fundamental analysis of its effect on performance[J]. Mathematical Problems in Engineering,2015,2015.DOI:10.1155/2015/851816.
[11] WU G Q, CHEN J, ZHU W J. Performance analysis and improvement of flat torque converters using DOE method[J]. Chinese Journal of Mechanical Engineering,2018,31(1):60.
[12] ABE H, TSURUOKA M, MUTO A, et al. Development of super ultra flat torque converter with multi plate lock-up clutch[J]. SAE International Journal of Engines,2009,2(1):48-55.
[13] SHIN S, BAE I C, JOO I S, et al. The effect of blade geometry on the performance of an automotive torque converter[C]. SAE Paper 2002-01-0885.
[14] JANDASEK V J. Design of single stage three element torque converter[C]. SAE Paper 610576.
[15] 朱喜林,黄伟,刘春宝,等.不同扁平率无内环液力变矩器设计与性能分析[J].农业机械学报,2011(6):33-37.DOI:10.3969/j.issn.1000-1298.2011.06.007.
[16] ASL H A, AZAD N L, MCPHEE J. Math-based modeling and parametric sensitivity analysis of torque converter performance characteristics[C]. SAE Paper 2011-01-0732.
[17] YAN Q D, LIU C, WEI W, et al. Numerical sensitivity analysis of the effect of pump outlet radius on the performance of torque converter[C]. Proceedings of the FISITA 2012 World Automotive Congress. Springer, Berlin, Heidelberg,2013:471-478.
[18] KUBO M, EJIRI E. A loss analysis design approach to improving torque converter performance[J]. SAE Transactions,1998:1644-1656.
[19] 韩克非,吴光强,王欢.基于 CFD 的泵轮叶栅关键参数对液力变矩器的性能影响预测[J].汽车工程,2010,32(6):497-500,465.
[20] SHIN S, CHANG H, JOO I S. Effect of scroll angle on performance of automotive torque converter[C]. SAE Paper 2000-01-1158.
[21] SHIN S, KIM K J, KIM D J, et al. The effect of reactor blade geometry on the performance of an automotive torque converter[J]. SAE Transactions,2002:1286-1293.
[22] 刘城,潘鑫,闫清东,等.基于DOE及RSM的液力变矩器叶片数对性能的影响及优化[J].北京理工大学学报,2012,32(7).DOI:10.3969/j.issn.1001-0645.2012.07.008.
[23] 范春顺.液力变矩器叶片数对其性能影响的研究[D].长春:吉林大学,2007.
[24] 马文星.液力传动理论与设计[M].北京:化学工业出版社,2004.
[25] WHITFIELD A, WALLACE F J, PATEL A. Design of three element hydrokinetic torque converters[J]. International Journal of Mechanical Sciences,1983,25(7):485-497.DOI:10.1016/0020-7403(83)90041-3.
[26] BY R R, MAHONEY J E. Technology needs for the automotive torque converter—part 1: internal flow, blade design, and performance[J]. SAE Transactions,1988:536-553.
[27] LIU S P, QUAN L. Mathematical model of hydrodynamic torque converter and analytic description of streamline[J]. Chinese Journal of Mechanical Engineering,2009,22(1):70-77.
[28] KESY A, KADZIELA A. Application of statistical formulas to hydrodynamic torque converter modelling[J]. Archives of Civil and Mechanical Engineering,2009,9(4):33-48.DOI:10.1016/S1644-9665(12)60067-3.
[29] 闫清东,邹波,魏巍.液力变矩减速装置制动特性流场分析[J].吉林大学学报(工学版),2012,42(1):91-97.
[30] LIU C B, LI J, BU W Y, et al. Application of scale-resolving simulation to a hydraulic coupling, a hydraulic retarder, and a hydraulic torque converter[J]. Journal of Zhejiang University-SCIENCE A,2018,19(12):904-925.
[31] DE LA FUENTE P, STOFF H, VOLGMANN W, et al. Numerical analysis into the effects of the unsteady flow in an automotive hydrodynamic torque converter[C]. Proceedings of theWorld Congress on Engineering,2011,3.
[32] WEI W, YAN Q D. Study on hydrodynamic torque converter parameter integrated optimization design system based on tri-dimensional flow field theory[J]. SAE International Journal of Fuels and Lubricants,2009,1(1):778-783.
[33] WU G Q, WANG L J. Multi-objective optimization employing genetic algorithm for the torque converter with dual-blade stator[C]. SAE Paper 2015-01-1119.
[34] WHITFIELD A, WALLACE F J, PATEL A. Performance prediction of multi element torque converters[J]. International Journal of Mechanical Sciences,1983,25(2):77-85.DOI:10.1016/0020-7403(83)90001-2.
[35] KIM B S, HA S B, LIM W S, et al. Performance estimation model of a torque converter part I: correlation between the internal flow field and energy loss coefficient[J]. International Journal of Automotive Technology,2008,9(2):141-148.
[36] LIU C, XIANG C L, YAN Q D, et al. Development and validation of a CFD based optimization procedure for the design of torque converter cascade[J]. Engineering Applications of Computational Fluid Mechanics,2019,13(1):128-141.DOI:10.1080/19942060.2018.1562383.
[37] 魏巍,闫清东.液力变矩器泵轮叶片优化设计研究[J].系统仿真学报,2008(23):6549-6552.
[38] 王安麟,孟庆华,曹岩,等.液力变矩器的叶片数神经网络模型[J].西安交通大学学报,2015,49(7):11-16.DOI:10.7652/xjtuxb201507003.
[39] LAKSHMINARAYANA B, DONG Y. Experimental and numerical investigation of stator exit flow field of an automotive torque converter[J]. Journal of Turbomachinery,1996,118:835.DOI:10.1115/1.2840941.
[40] DONG Y, LAKSHMINARAYANA B. Rotating probe measurements of the pump passage flow field in an automotive torque converter[J]. Transactions-American Society of Mechanical Engineers Journal of Fluids Engineering,2001,123(1):81-91.
[41] KRAUS S O, FLACK R, HABSIGER A, et al. Periodic velocity measurements in a wide and large radius ratio automotive torque converter at the pump/turbine interface[J]. Journal of Fluids Engineering,2005,127(2):308-316.DOI:10.1115/1.1891150.
[42] WU G Q, WANG L J. Application of dual-blade stator to low-speed ratio performance improvement of torque converters[J]. Chinese Journal of Mechanical Engineering,2016,29(2):293-300.
[43] WU G Q, YAN P. System for torque converter design and analysis based on CAD/CFD integrated platform[J]. Chinese Journal of Mechanical Engineering,2008,21(4):1.DOI:10.3901/CJME.2008.04.035.
[44] LIU C, UNTAROIU A, WOOD H G, et al. Parametric analysis and optimization of inlet deflection angle in torque converters[J]. Journal of Fluids Engineering,2015,137(3):031101.DOI:10.1115/1.4028596.
[45] SHIN S, LEE B C, HONG J H, et al. Performance improvement using a slotted stator of an automotive torque converter[C]. SAE Paper 2003-01-0247.
[46] 闫清东,李新毅,魏巍.基于多目标优化的液力变矩器叶形角度设计[J].华中科技大学学报(自然科学版),2017(9):13.DOI:10.13245/j.hust.170913.
[47] 李兴泉,邓兆祥,章竟成,等.基于响应面的液力变矩器叶片优化设计[J].华南理工大学学报(自然科学版),2011,39(11):149-154.DOI:10.3969/j.issn.1000-565X.2011.11.027.
[48] 闫清东,刘树成,魏巍,等.基于改进雷达图法的变矩器匹配评价[J].吉林大学学报(工学版),2013,43(6):1510-1516.DOI:10.7964/jdxbgxb201306013.
[49] WU H R, LI F, ZHANG H S. Computer aided calculation of matching between engine and hydraulic torque converter[C].2010 2nd International Conference on Future Computer and Communication. IEEE,2010,2:V2-6-V2-9.DOI:10.1109/ICFCC.2010.5497302.
[50] 孙跃东,周萍,邹敏,等.发动机与液力变矩器匹配的计算机软件开发[J].汽车工程,2004,26(6):702-704.
[51] WANG Z B, QIN S C. Optimization of matching on torque converter with engine based on improved radar chart method[C].2017 International Conference on Computer Network, Electronic and Automation (ICCNEA). IEEE,2017:370-373.DOI:10.1109/ICCNEA.2017.98.
[52] 陈凯,吴光强.基于遗传算法的液力变矩器与发动机匹配的多目标优化[J].汽车工程,2014,36(5):532-536.

Review on Design Optimization Research of Hydraulic Torque Converter for Passenger Vehicles

PDF (PC)

Like

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 15

Metrics

Comments

Recommended 10

[1]	Ping Liu, Zhuo Chen, Mingjie Liu, Changhao Piao, Soohyun Jang, Kailin Wan. Gauss Allocation Points Parameterization Parallel Automatic Parking Trajectory Planning for Vehicle Under Multi-Stage Constraints [J]. Automotive Engineering, 2023, 45(7): 1163-1173.
[2]	Jianhua Chen,Zhongming Xu,Zhifei Zhang. Suspension State Estimation Based on Wheelbase Preview at Variable Speed [J]. Automotive Engineering, 2023, 45(6): 1040-1049.
[3]	Yilin He,Jian Ma,Shukai Yang,Wei Zheng,Qifan Xue. Research on Stability Model Predictive Control of Intelligent Electric Vehicle with Preview Characteristics [J]. Automotive Engineering, 2023, 45(5): 719-734.
[4]	Zixian Li,Shiju Pan,Yuan Zhu,Binbing He,Youchun Xu. Semi-active Suspension Control for Intelligent Vehicles Based on State Feedback and Preview Feedforward [J]. Automotive Engineering, 2023, 45(5): 735-745.
[5]	Yanli Ma,Jun Lu,Jieyu Zhu,Xiaoxue Han. Take-over Performance Prediction Under Different Cognitive Loads of Non-driving Tasks in Highly Automated Driving [J]. Automotive Engineering, 2023, 45(12): 2330-2337.
[6]	Runhui Huang,Likun Hu,Mingfang Su,Daye Xu,Aoran Chen. Semantic Segmentation Method of LiDAR Point Cloud Based on 3D Conical Grid [J]. Automotive Engineering, 2022, 44(8): 1173-1182.
[7]	Yingshi Guo,Yahui Hu,Rui Fu,Chang Wang. Research on Driver Lateral Control Model Under Crosswind Conditions Based on Cognitive-Control Framework [J]. Automotive Engineering, 2022, 44(8): 1251-1261.
[8]	Longxin Guan,Zufei Gu,Chao Zhang,Aichun Wang,Chenruo Peng,Huihua Jiang,Xiaojian Wu. Model Predictive Path Following Control of Intelligent Vehicles Considering System Complex Disturbances [J]. Automotive Engineering, 2022, 44(12): 1844-1855.
[9]	Xiaokai Chen,Mingkai Zeng,Xiang Liu,An Jiang. Research on Semi-active Suspension Preview Control Based on VSL-MPC [J]. Automotive Engineering, 2022, 44(10): 1537-1546.
[10]	Jie Hu,Xinkai Zhong,Ruinan Chen,Linglei Zhu,Wencai Xu,Minchao Zhang. Path Tracking Control of Intelligent Vehicles Based on Fuzzy LQR [J]. Automotive Engineering, 2022, 44(1): 17-25.
[11]	Xiangyang Xu,Wenhao Hu,Honglei Dong,Yan Wang,Lingyun Xiao,Penghui Li. Review of Key Technologies for Autonomous Vehicle Test Scenario Construction [J]. Automotive Engineering, 2021, 43(4): 610-619.
[12]	Liu Xin, Liu Xiang, Zhou Zhenhua, Hu Lin. Design Optimization of Vehicle Occupant Restraint System Based on Adaptive Surrogate Model [J]. Automotive Engineering, 2020, 42(7): 887-893.
[13]	Wei Tonghui, Zuo Wenjie, Zheng Hongwei, Li Feng. Reliability-based Design Optimization of Car Body Based on Dimension Reduction Method [J]. Automotive Engineering, 2020, 42(7): 941-948.
[14]	Chen Wuwei, Wang Qidong, Ding Yukang, Zhao Linfeng, Wang Huiran, Xie Youhao. Weight Allocation Strategy Between Human and MachineBased on the Preview Distance to Lane Center [J]. Automotive Engineering, 2020, 42(4): 513-521.
[15]	Wang Yongsheng, Luo Yugong, Gu Yanchen, Chen Rui, Qi Yunlong, Jiang Fachao. Precise Adjustment Strategy of Autonomous Parking for Automatic Charging [J]. Automotive Engineering, 2020, 42(12): 1701-1709.