座椅体压分布仿真分析与评价

doi:10.19562/j.chinasae.qcgc.2018.09.014

摘要/Abstract

摘要： 本文中基于H点测量装置(HPM)建立了详细的座椅体压分布仿真模型,而与座椅体压分布仿真分析紧密相关的泡沫和面料的材料参数则通过拉伸和压缩试验获得。通过与试验对比不同区域的最大压力值、平均压力、接触面积和占重比4项评价指标来验证模型的可靠性。结果表明,所建立的模型不仅可以准确反映体压分布的一般规律,并且H点测量装置的肩部、腰部和大腿处的各项体压分布指标,仿真与试验误差在10%以内,座椅仿真模型有效。

关键词: 座椅, 体压分布, 检测, 泡沫, 仿真, 舒适性

Abstract: Based on the H-point machine (HPM), a detailed simulation model of body pressure distribution on seat is established in this paper. The material parameters of foam and fabric closely related to the simulation analysis of body pressure distribution on seat are obtained through tensile and compression tests. The reliability of the model is validated by comparing the maximum pressure, average pressure, contact area and weight ratio in different regions. The results show that the established model can not only accurately reflect the general rule of body pressure distribution, but also can accurately reflect the body pressure distribution indexes of shoulder, waist and thigh of the H-point machine. The error between the simulation and test is less than 10%, and the seat simulation model is effective.

Key words: seat, body pressure distribution, test , foam, simulation, comfort

沈重阳,张鹏,汪庆忠,李杨,杨戈,高伟. 座椅体压分布仿真分析与评价[J]. 汽车工程, 2018, 40(9): 1096-1100.

Shen Chongyang, Zhang Peng, Wang Qingzhong, Li Yang, Yang Ge & Gao Wei. Simulation Analysis and Evaluation of Body Pressure Distribution on Seat[J]. , 2018, 40(9): 1096-1100.

参考文献

[1] ANNETT J. Subjective rating scales in ergonomics: a reply[J] . Ergonomics,2010,45:1042-1046.
[2] MANENTCA I, CORLETT E N. A Model of vehicle comfort and a method for its assessment[J] . Ergonomics,2007,16(6):849-854.
[3] MA Jia, KE Yijie, SU Qiang, et al. An automobile seat comfort evaluating method based on artificial intelligence[J] . Mechanical Science and Technology for Aerospace Engineering,2011,30(3):419-422.
[4] JIN Xiaoping, YUAN Xiangke, WANG Bo. An objective evaluation method for the comfort of foam cushion in vehicle seat[J] . Automotive Engineering,2012,34(6):551-555.
[5] OUDENHUIJZEN A, TAN K, MORSCH F. The relationship between seat pressure and comfort[C] . SAE Paper 2003-01-2213.
[6] JIN X, CHENG B, WANG B, et al. Assessment of driver's seating discomfort using interface pressure distribution[C] . Intelligent Vehicles Symposium, IEEE,2009:1419-1424.
[7] ZHANG Yuhong, WANG Xin, HONG Jun, et al. Soft tissue stress distribution in hip-legs during sitting[J] . Journal of Xi′an Jiaotong University,2008,42(5):569-572.
[8] CHOI H Y, KIM K M, CHI H K, et al. Challenge of lumbar support design using human body models[J] . Sae International Journal of Passenger Cars Mechanical Systems,2008,1(1):1078-1084.
[9] SINGH P, RAINA S, PANDEY K K, et al. Effect of fabric type and construction on automotive seating comfort[C] . SAE Paper 2013-01-0654..
[10] Standard test method for compressive properties of rigid cellular plastic[S] . ASTM Standard D (2010) 1621-2010.
[11] 纺织品织物拉伸性能第1部分:断裂强力和断裂伸长率的测定(条样法):GB/T39231—2013[S] . 北京:中国标准出版社,2013.
[12] Society of Automotive Engineers. Recommended Practice J826,Devices for use in defining and measuring vehicle seating accommodation[S] . Warrendale PA: Society of Automotive Engineers, Inc,2002.
[13] HARTUNG J, MERGL C, BUBB H. Reliability of pressure measurement on car seats[C] . SAE Papers 2004-01-2167.
[14] XU Ming, et al. The parameters of body pressure distribution on seat[J] . China Mechanical Engineering,1997,8(1):65-68.

[1]	程腾,倪昊,张强,王文冲,石琴. 基于虚拟点云的二阶段多模态融合网络[J]. 汽车工程, 2024, 46(2): 222-229.
[2]	王庞伟,刘程,汪云峰,张名芳. 面向城市道路的智能网联汽车多车道轨迹优化方法[J]. 汽车工程, 2024, 46(2): 241-252.
[3]	刘凉,张滢,史晨阳,赵新华,孟宪明,刘增昌. 铆接铝合金板铆钉失效缺陷检测方法研究[J]. 汽车工程, 2024, 46(2): 366-374.
[4]	焦志鹏, 马建, 赵轩, 张凯, 孟德安, 韩琪, 张昭. 基于电动汽车制动安全检测的短时工况及方法研究[J]. 汽车工程, 2024, 46(1): 109-119.
[5]	高泽, 楚遵康, 石稼晟, 林滏, 饶卫雄, 余海燕. 基于图网络的汽车零部件应力场快速预测方法研究[J]. 汽车工程, 2024, 46(1): 170-178.
[6]	谷先广, 陈红林, 俞陆新, 张代胜. 精密铸铝件一体化设计及在车身轻量化中的应用[J]. 汽车工程, 2024, 46(1): 179-186.
[7]	王军年, 程川泰, 高菲, 付铁军, 任金东. 共享汽车驾驶员适宜H点和座椅参数实验研究[J]. 汽车工程, 2024, 46(1): 39-49.
[8]	马雷, 杨顺清, 王欢欢, 翟家琛, 徐健傲. 融合图像显著性特征的轻量级目标检测算法[J]. 汽车工程, 2024, 46(1): 84-91.
[9]	陈飞,孔祥栋,孙跃东,韩雪冰,卢兰光,郑岳久,欧阳明高. 锂离子电池制造工艺仿真技术进展[J]. 汽车工程, 2023, 45(9): 1516-1529.
[10]	马天飞,李波,朱冰,赵健. 考虑大气条件影响的自动泊车系统超声波雷达建模[J]. 汽车工程, 2023, 45(9): 1646-1654.
[11]	许有伟,陈桂银,吕平,赵振瑞,赵洋洋,孙茂喜,邢丹敏. 燃料电池系统仿真分析及测试验证[J]. 汽车工程, 2023, 45(9): 1710-1719.
[12]	刘启全,马建,赵轩,张凯,孟德安,相里康. 基于值率模型的电动汽车动力电池电压异常检测[J]. 汽车工程, 2023, 45(9): 1728-1739.
[13]	陈小勇,姚璐,郭正鑫,刘浩,罗挺,王永亮. B柱扰流器对风振噪声的影响及其机理[J]. 汽车工程, 2023, 45(9): 1772-1778.
[14]	刘卫国,项志宇,刘锐,李国栋,王子旭. 基于深度学习的端到端车辆运动规划方法研究[J]. 汽车工程, 2023, 45(8): 1343-1352.
[15]	赵东宇, 赵树恩. 基于级联YOLOv7的自动驾驶三维目标检测[J]. 汽车工程, 2023, 45(7): 1112-1122.